Microstructural and mechanical characterization of additively manufactured parts of maraging 18Ni300M steel with water and gas atomized powders feedstock

Registro completo de metadados
MetadadosDescriçãoIdioma
Autor(es): dc.contributorUniversidade de São Paulo (USP)-
Autor(es): dc.contributorUniversidade Estadual de Campinas (UNICAMP)-
Autor(es): dc.contributorUniversitat Politècnica de Catalunya (UPC)-
Autor(es): dc.contributorUniversidade Estadual Paulista (UNESP)-
Autor(es): dc.creatorPeinado, Gabriel-
Autor(es): dc.creatorCarvalho, Cauê-
Autor(es): dc.creatorJardini, André-
Autor(es): dc.creatorSouza, Eduardo-
Autor(es): dc.creatorAvila, Julián Arnaldo-
Autor(es): dc.creatorBaptista, Carlos-
Data de aceite: dc.date.accessioned2025-08-21T15:53:10Z-
Data de disponibilização: dc.date.available2025-08-21T15:53:10Z-
Data de envio: dc.date.issued2025-04-29-
Data de envio: dc.date.issued2023-12-31-
Fonte completa do material: dc.identifierhttp://dx.doi.org/10.1007/s00170-023-12686-2-
Fonte completa do material: dc.identifierhttps://hdl.handle.net/11449/301282-
Fonte: dc.identifier.urihttp://educapes.capes.gov.br/handle/11449/301282-
Descrição: dc.descriptionThe demand for manufacturing components with complex geometries, good mechanical properties, and material efficiency has surged across various industries, encompassing aerospace, military, nuclear, and naval sectors. Laser powder bed fusion (LPBF), as an additive manufacturing (AM) process, has emerged as a promising method for producing ultra-high mechanical strength alloys, like maraging 300 steel (18Ni300M). However, in numerous studies in the literature concerning the effects of processing parameters on the properties of 18Ni300M steel parts fabricated through LPBF, limited attention has been given to the influence that powder atomization methods may exert on the final properties of these parts. This article investigated the effect of gas atomization (GA) and water atomization (WA) processes on the microstructure of 18Ni300M steel powders and the mechanical properties, microstructure, and chemical composition of LPBF-produced parts. The results revealed significant distinctions in the morphology, aggregation degree, and particle size distribution between the GA and WA powders, which directly influenced the microstructure and affected the amount of defects in LPBF-produced parts. Despite the similar mechanical response found in the WA and GA specimens in the elastic region, the samples produced with the WA batch presented a brittle behavior with a ductility of only 4.06%, whereas the GA parts had an elastoplastic behavior with an elongation of 11.52%. The bulks from the WA batch produced in the LPBF process were compromised due to powder contamination with oxygen, which increased gas porosity and effected fragile oxide particles visible on the fracture surface.-
Descrição: dc.descriptionUniversitat Politècnica de Catalunya-
Descrição: dc.descriptionFundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)-
Descrição: dc.descriptionEngineering School of Lorena University of São Paulo (EEL/USP), Estrada Municipal Do Campinho, S/N, SP-
Descrição: dc.descriptionSchool of Chemical Engineering State University of Campinas (FEQ/UNICAMP), Avenida Albert Einstein, 500, SP-
Descrição: dc.descriptionResearch Group in Structures and Mechanics of Materials (REMM) Department of Strength of Materials and Structural Engineering Universitat Politècnica de Catalunya (UPC), Diagonal 647-
Descrição: dc.descriptionSchool of Engineering of São João da Boa Vista São Paulo State University, Av. Profa. Isette Corrèa Fontão, 505-
Descrição: dc.descriptionSchool of Engineering of São João da Boa Vista São Paulo State University, Av. Profa. Isette Corrèa Fontão, 505-
Descrição: dc.descriptionFAPESP: 2017/17697-5-
Descrição: dc.descriptionFAPESP: 2019/00691-0-
Descrição: dc.descriptionFAPESP: 2020/09079-2-
Formato: dc.format223-237-
Idioma: dc.languageen-
Relação: dc.relationInternational Journal of Advanced Manufacturing Technology-
???dc.source???: dc.sourceScopus-
Palavras-chave: dc.subjectAdditive manufacturing-
Palavras-chave: dc.subjectLaser powder bed fusion-
Palavras-chave: dc.subjectMaraging steel-
Palavras-chave: dc.subjectMechanical properties-
Palavras-chave: dc.subjectMicrostructural characterization-
Palavras-chave: dc.subjectPowder atomization-
Título: dc.titleMicrostructural and mechanical characterization of additively manufactured parts of maraging 18Ni300M steel with water and gas atomized powders feedstock-
Tipo de arquivo: dc.typelivro digital-
Aparece nas coleções:Repositório Institucional - Unesp

Não existem arquivos associados a este item.