Atenção:
O eduCAPES é um repositório de objetos educacionais, não sendo responsável por materiais de terceiros submetidos na plataforma. O usuário assume ampla e total responsabilidade quanto à originalidade, à titularidade e ao conteúdo, citações de obras consultadas, referências e outros elementos que fazem parte do material que deseja submeter. Recomendamos que se reporte diretamente ao(s) autor(es), indicando qual parte do material foi considerada imprópria (cite página e parágrafo) e justificando sua denúncia.
Caso seja o autor original de algum material publicado indevidamente ou sem autorização, será necessário que se identifique informando nome completo, CPF e data de nascimento. Caso possua uma decisão judicial para retirada do material, solicitamos que informe o link de acesso ao documento, bem como quaisquer dados necessários ao acesso, no campo abaixo.
Todas as denúncias são sigilosas e sua identidade será preservada. Os campos nome e e-mail são de preenchimento opcional. Porém, ao deixar de informar seu e-mail, um possível retorno será inviabilizado e/ou sua denúncia poderá ser desconsiderada no caso de necessitar de informações complementares.
Metadados | Descrição | Idioma |
---|---|---|
Autor(es): dc.contributor | McGill University | - |
Autor(es): dc.contributor | Mansoura University | - |
Autor(es): dc.contributor | Universidade Estadual Paulista (UNESP) | - |
Autor(es): dc.creator | Jafarpour, Dana | - |
Autor(es): dc.creator | El-Amier, Nesma | - |
Autor(es): dc.creator | Tahboub, Kawkab | - |
Autor(es): dc.creator | Zimmermann, Elizabeth | - |
Autor(es): dc.creator | Pero, Ana Carolina | - |
Autor(es): dc.creator | de Souza, Raphael | - |
Data de aceite: dc.date.accessioned | 2025-08-21T21:49:28Z | - |
Data de disponibilização: dc.date.available | 2025-08-21T21:49:28Z | - |
Data de envio: dc.date.issued | 2025-04-29 | - |
Data de envio: dc.date.issued | 2024-12-31 | - |
Fonte completa do material: dc.identifier | http://dx.doi.org/10.1016/j.prosdent.2025.02.035 | - |
Fonte completa do material: dc.identifier | https://hdl.handle.net/11449/298664 | - |
Fonte: dc.identifier.uri | http://educapes.capes.gov.br/handle/11449/298664 | - |
Descrição: dc.description | Statement of problem: The variety of recommended postprocessing techniques and printing parameters makes it challenging to determine the best approach to 3-dimensionally (3D) printed dentures. Purpose: The purpose of this in vitro study was to assess the effect of printing orientations (0, 45, and 90 degrees) and postprocessing treatments (ultraviolet [UV], heat, or combination) on the mechanical and surface properties of 3D printed denture base resin. Material and methods: Three-dimensionally printed denture base resin specimens were fabricated at 0-, 45-, and 90-degree printing orientations, followed by 4 postprocessing techniques (UV, Heat, UV+Heat, and control). Microhardness was assessed using a Vickers microhardness tester. Additionally, the flexural strength (FS) and modulus of elasticity (MoE) were analyzed using a 3-point bend test. Wettability was measured according to the sessile drop test. The fractured surfaces were observed under scanning electron microscopy (SEM). Results: FS was significantly greater (P<.001) at a print orientation of 90 degrees (73.7 MPa) compared with 0 and 45 degrees (55.2 and 61.8 MPa). No significant difference in FS was found among postprocessing treatments (all complied with the International Organization for Standardization [ISO] requirements). The UV group had the highest MoE (up to 2061 MPa), followed by the heat-treated groups (up to 1412 MPa). The 45-degree print orientation showed the highest contact angle (CA) in almost all groups (CA=117.6±11.7), and UV led to higher hydrophilicity (CA=33.9±12.0). The effect of build orientation on the microhardness depended on the postprocessing technique with the highest value (23.4 ±1.3) achieved by UV postprocessing in combination with the 90-degree orientation. Conclusions: The optimal FS of 3D printed denture base resin is achieved when it is printed in a vertical orientation (90 degrees relative to the platform base). Thermal annealing as a postprocessing technique combined with UV can effectively enhance FS, induce favorable wettability, and reduce stiffness. | - |
Descrição: dc.description | PhD Candidate Faculty of Dental Medicine and Oral Health Sciences McGill University | - |
Descrição: dc.description | PhD Candidate Faculty of Dental Medicine and Oral Health Sciences McGill University Montreal Quebec Canada; and Assistant Lecturer Prosthodontics Faculty of Dentistry Mansoura University | - |
Descrição: dc.description | Faculty of Dental Medicine and Oral Health Sciences McGill University | - |
Descrição: dc.description | Department of Dental Materials and Prosthodontics Araraquara Dental School São Paulo State University (UNESP) | - |
Descrição: dc.description | Faculty of Dental Medicine Université Laval Quebec Quebec Canada; and Adjunct Professor Faculty of Dental Medicine and Oral Health Sciences McGill University | - |
Descrição: dc.description | Department of Dental Materials and Prosthodontics Araraquara Dental School São Paulo State University (UNESP) | - |
Idioma: dc.language | en | - |
Relação: dc.relation | Journal of Prosthetic Dentistry | - |
???dc.source???: dc.source | Scopus | - |
Título: dc.title | Effects of DLP printing orientation and postprocessing regimes on the properties of 3D printed denture bases | - |
Tipo de arquivo: dc.type | livro digital | - |
Aparece nas coleções: | Repositório Institucional - Unesp |
O Portal eduCAPES é oferecido ao usuário, condicionado à aceitação dos termos, condições e avisos contidos aqui e sem modificações. A CAPES poderá modificar o conteúdo ou formato deste site ou acabar com a sua operação ou suas ferramentas a seu critério único e sem aviso prévio. Ao acessar este portal, você, usuário pessoa física ou jurídica, se declara compreender e aceitar as condições aqui estabelecidas, da seguinte forma: