Sintering mode of a translucent Y-TZP: Effects on its biaxial flexure fatigue strength, surface morphology and translucency

Registro completo de metadados
MetadadosDescriçãoIdioma
Autor(es): dc.contributorUniversidade Estadual Paulista (UNESP)-
Autor(es): dc.contributorUniversiteit van Amsterdam and Vrije Universiteit-
Autor(es): dc.contributorUniversidade Federal de Sergipe (UFS)-
Autor(es): dc.creatorMadruga, Camila Ferreira Leite-
Autor(es): dc.creatorDal Piva, Amanda Maria de Oliveira-
Autor(es): dc.creatorPereira, Gabriel Kalil Rocha-
Autor(es): dc.creatorCaneppele, Taciana Marco Ferraz-
Autor(es): dc.creatorValandro, Luiz Felipe-
Autor(es): dc.creatorBottino, Marco Antonio-
Data de aceite: dc.date.accessioned2025-08-21T17:19:21Z-
Data de disponibilização: dc.date.available2025-08-21T17:19:21Z-
Data de envio: dc.date.issued2023-03-02-
Data de envio: dc.date.issued2023-03-02-
Data de envio: dc.date.issued2021-12-31-
Fonte completa do material: dc.identifierhttp://dx.doi.org/10.1111/jerd.12923-
Fonte completa do material: dc.identifierhttp://hdl.handle.net/11449/241829-
Fonte: dc.identifier.urihttp://educapes.capes.gov.br/handle/11449/241829-
Descrição: dc.descriptionObjective: This investigation evaluated the effect of two sintering modes of a translucent zirconia (Y-TZP) on its surface roughness, topography, phase-transformation (t → m), translucency and biaxial flexure fatigue strength. Materials and Methods: To do so, 50 Y-TZP discs (Ø = 15 mm; thickness = 1.2 mm; IPS e.max ZirCAD LT) were prepared and divided into two groups: Standard mode (SM) and Fast mode (FM). Staircase fatigue testing was performed (piston-on-three balls set-up, ISO 6872:2015), as well as surface roughness, profilometry, scanning electron microscopy (SEM-FEG), energy dispersive X-ray spectroscopy (EDX), phase transformation (t → m) using X-ray diffraction analysis (XRD), translucency parameter analysis (TP and TP00) and fractography. Results: The results showed no statistical significant differences for roughness parameters (p > 0.05, SM: Ra = 0.13 ± 0.02, Rz = 1.21 ± 0.26 and RSm = 24.91 ± 2.19; FM: Ra = 0.14 ± 0.03, Rz = 1.32 ± 0.25 and RSm = 24.68 ± 2.16) or flexural fatigue strength (SM: 512 (464–560) MPa; FM: 542 (472–611) MPa) between the groups. In addition, similarity in surface morphological features (SEM and profilometry), composition and phases (EDX and XRD) was observed between the firing protocols. Fractography showed that the failure origin occurred on the tensile side. Sintering mode did not affect the TP (F = 0.001, p = 0.97) and TP00 (F = 0.12, p = 0.72). Conclusions: Therefore, the fast-sintering mode is suggested as a viable alternative to the standard mode since it does not influence the evaluated surface morphology, microstructure, fatigue strength and translucency of a translucent monolithic zirconia. Clinical Significance: The fast sintering mode is a viable alternative for zirconia without compromising its topography, microstructure, mechanical performance or translucency.-
Descrição: dc.descriptionPost-Graduate Program in Applied Sciences to Oral Health (Restorative Dentistry) São Paulo State University (Unesp) Institute of Science and Technology, São Paulo State-
Descrição: dc.descriptionDepartment of Dental Materials Science Academic Centre for Dentistry Amsterdam (ACTA) Universiteit van Amsterdam and Vrije Universiteit, Noord-Holland-
Descrição: dc.descriptionPost-Graduate Program in Oral Science (Prosthodontics Units) Faculty of Dentistry Federal University of Santa Maria (UFSM), Rio Grande do Sul State-
Descrição: dc.descriptionPost-Graduate Program in Applied Sciences to Oral Health (Restorative Dentistry) São Paulo State University (Unesp) Institute of Science and Technology, São Paulo State-
Idioma: dc.languageen-
Relação: dc.relationJournal of Esthetic and Restorative Dentistry-
???dc.source???: dc.sourceScopus-
Palavras-chave: dc.subjectfatigue-
Palavras-chave: dc.subjectfractography-
Palavras-chave: dc.subjectprosthodontics-
Palavras-chave: dc.subjectsintering-
Palavras-chave: dc.subjecttranslucent zirconia-
Título: dc.titleSintering mode of a translucent Y-TZP: Effects on its biaxial flexure fatigue strength, surface morphology and translucency-
Tipo de arquivo: dc.typelivro digital-
Aparece nas coleções:Repositório Institucional - Unesp

Não existem arquivos associados a este item.