Atenção:
O eduCAPES é um repositório de objetos educacionais, não sendo responsável por materiais de terceiros submetidos na plataforma. O usuário assume ampla e total responsabilidade quanto à originalidade, à titularidade e ao conteúdo, citações de obras consultadas, referências e outros elementos que fazem parte do material que deseja submeter. Recomendamos que se reporte diretamente ao(s) autor(es), indicando qual parte do material foi considerada imprópria (cite página e parágrafo) e justificando sua denúncia.
Caso seja o autor original de algum material publicado indevidamente ou sem autorização, será necessário que se identifique informando nome completo, CPF e data de nascimento. Caso possua uma decisão judicial para retirada do material, solicitamos que informe o link de acesso ao documento, bem como quaisquer dados necessários ao acesso, no campo abaixo.
Todas as denúncias são sigilosas e sua identidade será preservada. Os campos nome e e-mail são de preenchimento opcional. Porém, ao deixar de informar seu e-mail, um possível retorno será inviabilizado e/ou sua denúncia poderá ser desconsiderada no caso de necessitar de informações complementares.
Metadados | Descrição | Idioma |
---|---|---|
Autor(es): dc.contributor | Jacarezinho Campus | - |
Autor(es): dc.contributor | Universidade Estadual Paulista (UNESP) | - |
Autor(es): dc.creator | Ribeiro, Fernando Sabino Fonteque | - |
Autor(es): dc.creator | Lopes, José Claudio | - |
Autor(es): dc.creator | Rodriguez, Rafael Lemes | - |
Autor(es): dc.creator | de Angelo Sanchez, Luiz Eduardo | - |
Autor(es): dc.creator | de Mello, Hamilton José | - |
Autor(es): dc.creator | de Aguiar, Paulo Roberto | - |
Autor(es): dc.creator | Bianchi, Eduardo Carlos | - |
Data de aceite: dc.date.accessioned | 2025-08-21T23:35:35Z | - |
Data de disponibilização: dc.date.available | 2025-08-21T23:35:35Z | - |
Data de envio: dc.date.issued | 2022-04-29 | - |
Data de envio: dc.date.issued | 2022-04-29 | - |
Data de envio: dc.date.issued | 2020-12-31 | - |
Fonte completa do material: dc.identifier | http://dx.doi.org/10.1007/s00170-021-07757-1 | - |
Fonte completa do material: dc.identifier | http://hdl.handle.net/11449/229317 | - |
Fonte: dc.identifier.uri | http://educapes.capes.gov.br/handle/11449/229317 | - |
Descrição: dc.description | The grinding of interrupted geometries, such as keyways, holes, lubrication channels and crankshafts, bearings, helical drills, sharpening, and gear hobbing process for pre-toothing, presents technical difficulties such as decrease in surface quality and an increase in costs, when compared to continuous grinding process. This work aims to study further findings about interrupted cylindrical grinding process of AISI 4340 steel, with the application of resinoid aluminum oxide grinding wheel and conventional application of MWF. In a novel and innovative way, this work analyzed the wheel wear cost at 3 different feed rates (0.25, 0.50, and 0.75 mm/min) for continuous workpieces and interrupted workpieces with 2, 6, and 12 grooves. In addition, surface roughness, roundness deviation, grinding power, tangential force, microstructural analysis, diametrical wear, and G ratio were also evaluated. In conclusion to the results obtained, the average values of surface roughness Ra and Rz increased with the severity of the process (feed rate and number of grooves). For feed rates varying from 0.25 to 0.75 mm/min, mean values of 0.51 to 1.10 μm (Ra) and 4.52 to 10.99 μm (Rz) were obtained for the condition with 12 interruptions, indicating an increase in the order of 75 to 114% compared to without interrupted workpiece. The quick wear of the wheel, obtained for an average diametrical wheel wear of 5.79 μm for workpiece with 12 interruptions in 0.75 mm/min, produced higher surface roughness values. Variations of more than 80% in roundness deviation were obtained during grinding at feed rates of 0.75 mm/min due to mechanical shocks during material removal process, being observed in force variations from 50 to 700 N. The cost analysis of grinding wheel wear showed the waste of abrasive material for grinding process with interrupted geometries. For all tests, the tool cost for low feed rate (0.25 mm/min) did not suffer great variations. For feed rates of 0.50 and 0.75 mm/min, the cost of tool wear was higher. The condition with the highest percentage increase in cost was recorded for grinding process with workpiece of 12 grooves and feed rate of 0.75 mm/min, generating an increase of up to 1720% in the tool cost. Converting into monetary values, the wheel cost is of $ 12.62 per 1000-piece batch. | - |
Descrição: dc.description | Department of Control and Industrial Process Federal Institute of Paraná Jacarezinho Campus | - |
Descrição: dc.description | Department of Mechanical Engineering São Paulo State University “Júlio de Mesquita Filho” Bauru Campus | - |
Descrição: dc.description | Department of Mechanical Engineering São Paulo State University “Júlio de Mesquita Filho” Bauru Campus | - |
Idioma: dc.language | en | - |
Relação: dc.relation | International Journal of Advanced Manufacturing Technology | - |
???dc.source???: dc.source | Scopus | - |
Palavras-chave: dc.subject | AISI 4340 | - |
Palavras-chave: dc.subject | Discontinuous grinding | - |
Palavras-chave: dc.subject | External cylindrical grinding process | - |
Palavras-chave: dc.subject | Number of grooves | - |
Palavras-chave: dc.subject | Resinoid aluminum oxide wheel | - |
Palavras-chave: dc.subject | Surface integrity | - |
Palavras-chave: dc.subject | Wheel wear cost | - |
Título: dc.title | Novel performance assessment of interrupted grinding process using aluminum oxide wheel with resinoid bond | - |
Tipo de arquivo: dc.type | livro digital | - |
Aparece nas coleções: | Repositório Institucional - Unesp |
O Portal eduCAPES é oferecido ao usuário, condicionado à aceitação dos termos, condições e avisos contidos aqui e sem modificações. A CAPES poderá modificar o conteúdo ou formato deste site ou acabar com a sua operação ou suas ferramentas a seu critério único e sem aviso prévio. Ao acessar este portal, você, usuário pessoa física ou jurídica, se declara compreender e aceitar as condições aqui estabelecidas, da seguinte forma: