The shock wave configuration used in nonlinear transmission lines to improve the voltage modulation depth

Registro completo de metadados
MetadadosDescriçãoIdioma
Autor(es): dc.contributorUniversidade de São Paulo (USP)-
Autor(es): dc.contributorAssociated Plasma Laboratory-
Autor(es): dc.contributorDept. of Elect. and Comp. Engineering-
Autor(es): dc.contributorUniversidade Estadual Paulista (UNESP)-
Autor(es): dc.creatorSilva Neto, L. P.-
Autor(es): dc.creatorSantos Junior, V. C.-
Autor(es): dc.creatorRossi, J. O.-
Autor(es): dc.creatorBarroso, J. J.-
Autor(es): dc.creatorSchamiloglu, E.-
Autor(es): dc.creatorRangel, E. G.L.-
Autor(es): dc.creatorLima, G.-
Autor(es): dc.creatorSantos, L. F.-
Data de aceite: dc.date.accessioned2025-08-21T19:22:53Z-
Data de disponibilização: dc.date.available2025-08-21T19:22:53Z-
Data de envio: dc.date.issued2022-04-28-
Data de envio: dc.date.issued2022-04-28-
Data de envio: dc.date.issued2020-12-31-
Fonte completa do material: dc.identifierhttp://dx.doi.org/10.1109/PPC40517.2021.9733052-
Fonte completa do material: dc.identifierhttp://hdl.handle.net/11449/223734-
Fonte: dc.identifier.urihttp://educapes.capes.gov.br/handle/11449/223734-
Descrição: dc.descriptionNonlinear transmission lines (NLTLs) using varactor diodes can produce high-frequency waves on the order of some tens of megahertz. They reach only low power signals, and a way to improve the voltage modulation depth (VMD) without employing semiconductor devices is by using shock wave configuration. The shock wave configuration consists of several lines in parallel connected to the same source and the load. The main electrical parameters analyzed in these lines are frequency, VMD, power, and the number of lumped-element sections. This work proposes the shock wave configuration for improving the VMD using multiple NLTLs. NLTLs in the shock wave configuration were implemented on printed circuit boards and simulated by using the LT-Spice software. Simulation and tests of a single line with 7 lumped-sections produced an RF signal at a frequency of about 30 MHz, VMD around 0.79 V. On the other hand, by using a shock wave configuration with four lines, the VMD increased to 3.73 V, which means a gain of 4.72. Other parameters remained unchanged under the shock wave configuration.-
Descrição: dc.descriptionFederal University of São Paulo Dept.of Science and Technology-
Descrição: dc.descriptionNational Institute for Space Research Associated Plasma Laboratory-
Descrição: dc.descriptionUniversity of New Mexico Dept. of Elect. and Comp. Engineering-
Descrição: dc.descriptionSão Paulo State University Physics Departament-
Descrição: dc.descriptionSão Paulo State University Physics Departament-
Idioma: dc.languageen-
Relação: dc.relationIEEE International Pulsed Power Conference-
???dc.source???: dc.sourceScopus-
Palavras-chave: dc.subjectNLTLs-
Palavras-chave: dc.subjectradiofrequency-
Palavras-chave: dc.subjectshock wave configuration-
Palavras-chave: dc.subjectvaractor diode-
Título: dc.titleThe shock wave configuration used in nonlinear transmission lines to improve the voltage modulation depth-
Tipo de arquivo: dc.typeaula digital-
Aparece nas coleções:Repositório Institucional - Unesp

Não existem arquivos associados a este item.