Improving precision in aluminum alloy machining due to the application of diamond-like carbon thin film

Registro completo de metadados
MetadadosDescriçãoIdioma
Autor(es): dc.contributorUniversidade Estadual Paulista (Unesp)-
Autor(es): dc.contributorFiat Chrysler Group-
Autor(es): dc.contributorUniversidade Federal de Minas Gerais (UFMG)-
Autor(es): dc.contributorPontifical Catholic University of Minas Gerais-
Autor(es): dc.creatorDe Melo Silva, William [UNESP]-
Autor(es): dc.creatorMartins, Paulo Sérgio-
Autor(es): dc.creatorDe Carvalho, Vagner Eustáquio-
Autor(es): dc.creatorDa Cruz, Nilson Cristino [UNESP]-
Autor(es): dc.creatorClaudino, Enzo [UNESP]-
Autor(es): dc.creatorCarneiro, José Rubens Gonçalves-
Data de aceite: dc.date.accessioned2022-02-22T00:47:06Z-
Data de disponibilização: dc.date.available2022-02-22T00:47:06Z-
Data de envio: dc.date.issued2021-06-25-
Data de envio: dc.date.issued2021-06-25-
Data de envio: dc.date.issued2021-07-01-
Fonte completa do material: dc.identifierhttp://dx.doi.org/10.1115/1.4048723-
Fonte completa do material: dc.identifierhttp://hdl.handle.net/11449/206442-
Fonte: dc.identifier.urihttp://educapes.capes.gov.br/handle/11449/206442-
Descrição: dc.descriptionCutting precision is extremely affected by a phenomenon known as built up edge (BUE) that occurs on tungsten carbide tools during low cutting speed of aluminum alloy. BUE is responsible for early tool breakage due to excessive material build up from the machined part on the cutting face, leading to problems of shape irregularity and tool-tip breakage. Thus, diamond-like carbon (DLC) was deposited and tested to verify cutting precision in aluminum alloy by using tungsten carbide tools. The characterizations of the film were morphology analysis through scanning electron microscopy (SEM), structural atomic analyze of chemical bond from Raman backscatter spectroscopy, the distribution of carbon atoms on the film surface by X-ray photoelectron spectroscopy (XPS), and the evaluation of Young's modulus and hardness using the Oliver-Pharr method. To analyze the cutting precision, drilling tests were performed on coated/uncoated drills at two cutting speeds (340 and 430 m/min). As an evaluation parameter in the aluminum alloy, the hole diameter deviation was measured after pre determined numbers of drilling operations. Statistical comparisons between the diameter deviation as a function of the number of drilling test indicated better cutting accuracy for the DLC-coated tool. The factors identified in this work, such as the reduction of the friction coefficient, and the hardness and Young's modulus of the DLC helped in the performance of the tool, mainly in the lower cutting speed.-
Descrição: dc.descriptionFundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)-
Descrição: dc.descriptionMaterial Science and Engineering Laboratory São Paulo State University IBTEC-UNESP, Al. Tecomarias s/n-
Descrição: dc.descriptionFiat Chrysler Group, Av. Contorno, 3455-
Descrição: dc.descriptionDepartment of Physics Federal University of Minas Gerais, Av. Presidente Antônio Carlos 6627-
Descrição: dc.descriptionLaboratory of Technological Plasmas Institute of Science and Technology São Paulo State University, Av. Três de Março 511-
Descrição: dc.descriptionDepartment of Mechanical Engineering Pontifical Catholic University of Minas Gerais, Av. Dom JoséGaspar 500-
Descrição: dc.descriptionMaterial Science and Engineering Laboratory São Paulo State University IBTEC-UNESP, Al. Tecomarias s/n-
Descrição: dc.descriptionLaboratory of Technological Plasmas Institute of Science and Technology São Paulo State University, Av. Três de Março 511-
Descrição: dc.descriptionFAPESP: 2015/20438-6-
Idioma: dc.languageen-
Relação: dc.relationJournal of Tribology-
???dc.source???: dc.sourceScopus-
Palavras-chave: dc.subjectAlloy-
Palavras-chave: dc.subjectAluminum-
Palavras-chave: dc.subjectBuilt up edge-
Palavras-chave: dc.subjectCarbide-
Palavras-chave: dc.subjectDiamond-like carbon-
Palavras-chave: dc.subjectMachining-
Palavras-chave: dc.subjectTungsten-
Título: dc.titleImproving precision in aluminum alloy machining due to the application of diamond-like carbon thin film-
Tipo de arquivo: dc.typelivro digital-
Aparece nas coleções:Repositório Institucional - Unesp

Não existem arquivos associados a este item.