Atenção: Todas as denúncias são sigilosas e sua identidade será preservada.
Os campos nome e e-mail são de preenchimento opcional
Metadados | Descrição | Idioma |
---|---|---|
Autor(es): dc.contributor | Universidade Estadual Paulista (Unesp) | - |
Autor(es): dc.contributor | Sao Paulo State Technol Coll | - |
Autor(es): dc.contributor | Universidade de São Paulo (USP) | - |
Autor(es): dc.creator | Rodriguez, Rafael Lemes [UNESP] | - |
Autor(es): dc.creator | Lopes, Jose Claudio [UNESP] | - |
Autor(es): dc.creator | Garcia, Mateus Vinicius [UNESP] | - |
Autor(es): dc.creator | Tarrento, Gilson Eduardo | - |
Autor(es): dc.creator | Rodrigues, Alessandro Roger | - |
Autor(es): dc.creator | Angelo Sanchez, Luiz Eduardo de [UNESP] | - |
Autor(es): dc.creator | Mello, Hamilton Jose de [UNESP] | - |
Autor(es): dc.creator | Aguiar, Paulo Roberto de [UNESP] | - |
Autor(es): dc.creator | Bianchi, Eduardo Carlos [UNESP] | - |
Data de aceite: dc.date.accessioned | 2022-02-22T00:09:57Z | - |
Data de disponibilização: dc.date.available | 2022-02-22T00:09:57Z | - |
Data de envio: dc.date.issued | 2020-12-09 | - |
Data de envio: dc.date.issued | 2020-12-09 | - |
Data de envio: dc.date.issued | 2020-02-25 | - |
Fonte completa do material: dc.identifier | http://dx.doi.org/10.1007/s00170-020-05122-2 | - |
Fonte completa do material: dc.identifier | http://hdl.handle.net/11449/196616 | - |
Fonte: dc.identifier.uri | http://educapes.capes.gov.br/handle/11449/196616 | - |
Descrição: dc.description | Although the fact that the interrupted cutting process is widely employed in traditional machining operations such as turning of crankshafts, engine piston ring, and helical tool sharpening, only a few number of studies in the literature approach this process. This study aims to evaluate the performance of the interrupted grinding process of workpieces with a different number of grooves (2, 6, and 12) in CBN grinding and to contribute to further findings about the integrity of interrupted surfaces and groove flanks after grinding, analyzing surface roughness and roundness deviation of workpieces after grinding process. The diametric wheel wear and grinding power were also recorded and analyzed. The performance of the interrupted grinding process was compared with the continuous grinding process, i.e., for workpieces without grooves. The AISI 4340 steel workpieces were tested under the application of flood lubri-cooling method at different feed rates (0.25, 0.50, and 0.75 mm/min). In conclusion, higher feed rate increased the surface roughness from 0.12 to 0.35 mu m for continuous grinding process, respectively at 0.25 and 075 mm/min. The interrupted grinding led to increase of surface roughness Ra values from 0.19 to 0.43 mu m (respectively 58.3% and 22.9% higher than continuous) for 2 grooves, 0.31 to 0.59 mu m (respectively 158.3% and 68.6% higher than continuous) for 6 grooves and 0.54 to 0.93 mu m (respectively 341.7% and 165.7% higher than continuous) for 12 grooves, respectively at 0.25 and 0.75 mm/min. As presented for surface roughness values, the increase of groove number resulted in higher values of roundness deviation, diametric wheel wear due to mechanical shocks caused by couplings and uncouplings of the grinding wheel. It was evidenced by SEM images of groove flanks and macro-fracture mode of abrasive grains. No microstructural damage was caused by thermal or mechanical irrespective of the experimental conditions investigated. | - |
Descrição: dc.description | company Nikkon Ferramentas de Corte Ltda - Saint Gobain Group | - |
Descrição: dc.description | Quimatic Tapmatic Ltda | - |
Descrição: dc.description | Sao Paulo State Univ, Dept Mech Engn, Bauru Campus, Bauru, SP, Brazil | - |
Descrição: dc.description | Sao Paulo State Technol Coll, Botucatu Campus, Botucatu, SP, Brazil | - |
Descrição: dc.description | Univ Sao Paulo, Sch Engn Sao Carlos, Sao Carlos, SP, Brazil | - |
Descrição: dc.description | Sao Paulo State Univ, Dept Mech Engn, Bauru Campus, Bauru, SP, Brazil | - |
Formato: dc.format | 1265-1275 | - |
Idioma: dc.language | en | - |
Publicador: dc.publisher | Springer | - |
Relação: dc.relation | International Journal Of Advanced Manufacturing Technology | - |
???dc.source???: dc.source | Web of Science | - |
Palavras-chave: dc.subject | Grinding process | - |
Palavras-chave: dc.subject | Interrupted cutting | - |
Palavras-chave: dc.subject | Number of grooves | - |
Palavras-chave: dc.subject | Hardened steel | - |
Palavras-chave: dc.subject | CBN grinding wheel | - |
Palavras-chave: dc.subject | Geometric errors | - |
Palavras-chave: dc.subject | Diametric wheel wear | - |
Palavras-chave: dc.subject | Surface integrity | - |
Título: dc.title | Grinding process applied to workpieces with different geometries interrupted using CBN wheel | - |
Tipo de arquivo: dc.type | livro digital | - |
Aparece nas coleções: | Repositório Institucional - Unesp |
O Portal eduCAPES é oferecido ao usuário, condicionado à aceitação dos termos, condições e avisos contidos aqui e sem modificações. A CAPES poderá modificar o conteúdo ou formato deste site ou acabar com a sua operação ou suas ferramentas a seu critério único e sem aviso prévio. Ao acessar este portal, você, usuário pessoa física ou jurídica, se declara compreender e aceitar as condições aqui estabelecidas, da seguinte forma: