Does airborne-particle abrasion before, rather than after, zirconia sintering lead to higher mechanical strength even under aging challenge?

Registro completo de metadados
MetadadosDescriçãoIdioma
Autor(es): dc.contributorUniversidade Estadual Paulista (UNESP)-
Autor(es): dc.creatorMartins, Samira Branco-
Autor(es): dc.creatorTrindade, Flávia Zardo-
Autor(es): dc.creatorGóes, Márcio de Sousa-
Autor(es): dc.creatorAdabo, Gelson Luis-
Autor(es): dc.creatorDovigo, Lívia Nordi-
Autor(es): dc.creatorFonseca, Renata Garcia-
Data de aceite: dc.date.accessioned2021-03-11T01:37:28Z-
Data de disponibilização: dc.date.available2021-03-11T01:37:28Z-
Data de envio: dc.date.issued2019-10-06-
Data de envio: dc.date.issued2019-10-06-
Data de envio: dc.date.issued2019-01-01-
Fonte completa do material: dc.identifierhttp://dx.doi.org/10.1016/j.prosdent.2018.10.022-
Fonte completa do material: dc.identifierhttp://hdl.handle.net/11449/188996-
Fonte: dc.identifier.urihttp://educapes.capes.gov.br/handle/11449/188996-
Descrição: dc.descriptionStatement of problem: Information concerning the effect of airborne-particle abrasion before zirconia sintering on its strength after aging is lacking. Purpose: The purpose of this in vitro study was to determine the influence of airborne-particle abrasion moment (before or after zirconia sintering), particle size, and aging on the mechanical strength of a yttria-stabilized tetragonal zirconia polycrystalline ceramic. Material and methods: Four hundred presintered zirconia disks were allocated to nonabraded (control) and abraded groups with 50 μm or 120 μm Al 2 O 3 particles before (50/BS or 120/BS) or after sintering (50/AS or 120/AS). The disks were aged by storing them in distilled water for 24 hours at 37°C (24 h) (control); mechanical cycling (MC) (1×10 6 cycles; 2 Hz; 100 N); hydrothermal aging (HA) (134°C; 0.2 MPa; 20 hours); or by both methods (MC+HA), totaling 20 groups (n=20). The specimens were subjected to biaxial flexural strength (BFS) testing. Fractographic analysis was performed to identify the fracture origin. Tetragonal to monoclinic transformation was determined by X-ray diffraction. The BFS data (MPa) were analyzed by 2-way ANOVA and the Games-Howell post hoc test (α=.05). Weibull statistics was also applied. Results: The BFS and characteristic strength (σ0) of the 120/AS groups were significantly higher compared with the other abraded groups and statistically similar or higher compared with the respective nonabraded groups. In contrast, the 120/BS/24 h and all the 50/BS groups presented the lowest values. In all groups, the initial defect had its origin on the tensile stress side. Neither airborne-particle abrasion nor aging (except for the 50/AS/MC+HA) reduced the zirconia reliability compared with the respective controls. Abrading the zirconia in its presintered stage or after sintering increased the monoclinic phase content, and the sintering process eliminated this phase. Conclusions: Airborne-particle abrasion before zirconia sintering yields an inferior performance compared with that after sintering under aging challenges. The BFS and σ0 were strongly determined by the particle size and airborne-particle abrasion moment, while aging mainly acted in the nonabraded zirconia or when this material was abraded before sintering.-
Idioma: dc.languageen-
Relação: dc.relationJournal of Prosthetic Dentistry-
Direitos: dc.rightsopenAccess-
Título: dc.titleDoes airborne-particle abrasion before, rather than after, zirconia sintering lead to higher mechanical strength even under aging challenge?-
Tipo de arquivo: dc.typelivro digital-
Aparece nas coleções:Repositório Institucional - Unesp

Não existem arquivos associados a este item.